1
What's in the Blend
GHK-Cu · 50mg
Copper
Peptide
Peptide
Collagen & Gene Expression
Highest dose in this blend
Activates collagen synthesis genes, reduces inflammatory breakdown of skin tissue, and resets skin toward younger expression patterns. GHK-Cu is the backbone of this stack.
BPC-157 · 10mg
Body Protecting
Compound 157
Compound 157
Local Repair
Equal ratio with TB-500
Promotes angiogenesis (blood vessel growth) and growth factor release. Drives local tissue repair at the injection site — gets more blood flow and healing signals into the area.
TB-500 · 10mg
Thymosin
Beta-4 Fragment
Beta-4 Fragment
Systemic Healing
Equal ratio with BPC-157
Sends body-wide cell migration and tissue remodeling signals. Works systemically — not just locally — so it supports regeneration throughout the body, not just at the injection site.
All three compounds ship pre-mixed in a single vial. You reconstitute once and every injection automatically delivers all three proportionally. GHK-Cu is dosed at 5× the others — this is intentional. Each draw delivers significantly more GHK-Cu relative to BPC-157 and TB-500.
2
Reconstitution
One Vial — Reconstitute Once
| Vial Contents | Bacteriostatic Water | Per Unit on Syringe | Notes |
|---|---|---|---|
| GLOW Blend (50/10/10mg) | Add 2 mL | 0.25mg GHK-Cu + 0.05mg BPC-157 + 0.05mg TB-500 | GHK-Cu is intentionally higher — each draw delivers proportionally more |
Tilt the vial at an angle and inject bacteriostatic water slowly down the side — do not aim the stream directly at the powder. Swirl gently until dissolved. Do not shake. Refrigerate immediately after mixing.
Watch: How to Reconstitute a Peptide Vial
Add 2mL of bacteriostatic water to your GLOW vial. Because all three compounds are pre-mixed, every draw automatically delivers the correct ratio of all three.
3
How to Inject
Method
SubQ
Into the fat layer just under the skin
Injection Site
Belly fat or upper chest/shoulder
For face/neck targets: upper chest or shoulder is the closest safe SubQ site — do not inject into the face
Needle Angle
45°
Pinch skin, insert at a shallow angle
Timing
Morning or evening
Once daily — pick one time and stay consistent
4
Dosing Tiers
Slow & Steady
10 units
once per day
~0.5mg GHK-Cu
~0.1mg BPC-157
~0.1mg TB-500
Best For
Gentle daily dose for general skin maintenance and introduction
Most Popular
Suggested
20 units
once per day
~1mg GHK-Cu
~0.2mg BPC-157
~0.2mg TB-500
Best For
Community sweet spot for visible skin improvement and anti-aging
Aggressive but Safe
40 units
once per day
~2mg GHK-Cu
~0.4mg BPC-157
~0.4mg TB-500
✓ Well-tolerated at this dose
Best For
Targeting significant skin improvement or anti-aging in shorter cycles
5
Titration Schedule
All 3 protocols — ramp up over first 2 weeks
| Week | Slow & Steady | Suggested | Aggressive |
|---|---|---|---|
| Week 1 | 10 units | 10 units | 10 units |
| Week 2 | 10 units | 20 units | 20 units |
| Week 3+ | 10 units | 20 units | 40 units |
6
Cycle Length
Run daily — then take a break
4–8
Weeks On
One injection daily from the GLOW vial for the full cycle
4
Weeks Off
Full break between cycles — allows the skin to consolidate gains
Longer
Slow & Steady
Can run the Slow & Steady dose continuously without a hard break
What to Expect
- Weeks 1–2: Improved skin hydration and texture. The skin feels more supple and less dry.
- Weeks 3–4: Fine line reduction begins. Skin tone becomes more even. Collagen improvement is underway.
- Weeks 6–8: Visible anti-aging effects. Results continue to build — skin regeneration takes time and compounds across cycles.
7
Protocol Rules
Do
- Inject consistently at the same time each day
- Keep the vial refrigerated after reconstitution
- Pair with SPF and hydration for best results
- Be patient — skin regeneration takes weeks, not days
Don't
- Expect overnight results — this is a weeks-long process
- Shake the vial — swirl gently only
- Inject into the face directly — SubQ on the body near the target area only
- Use tap or distilled water — bacteriostatic water only
Also Available
GLOW 80mg Pen
Same GLOW blend — GHK-Cu + BPC-157 + TB-500 — in an auto-injector pen format. No vials, no syringes, no reconstitution. Just click and inject. Ask us about it: info@peptidestandard.health or text (714) 376-9013
↗
Supplies You'll Need
Insulin Syringes (for injection)
Use one fresh syringe per injection. 29–31 gauge ensures minimal discomfort for SubQ use.
Reconstitution Syringe
For mixing only — do NOT use for injection. Used to transfer bacteriostatic water into the vial.
Alcohol Swabs
Wipe the vial top and injection site before every use.
→
Individual Compound Guides
Go Deeper
Want the full breakdown on each compound in the GLOW Blend?
Each has its own standalone protocol guide.
Each has its own standalone protocol guide.